- What is ACL and what are the major types available?
- How does Cisco Show ACL?
- What are the types of ACL?
- How do I check the ACL on my router?
- What is the difference between ACL and firewall?
- What is ACL authentication?
- Where is standard ACL applied?
- Which scenario would cause an ACL misconfiguration and deny all traffic?
- What is the effect of configuring an ACL with only ACEs that deny traffic?
- How does Cisco ACL work?
- On which options are standard ACL based?
- What command will show you if an ACL is applied to an interface?
- What is ACL command?
- What extended ACL?
- Where do you put an extended ACL?
What is ACL and what are the major types available?
There are several types of access control lists and most are defined for a distinct purpose or protocol.
On Cisco routers, there are two main types: standard and extended.
Reflexive ACLs, also known as IP Session ACLs, are triggered from an outbound ACL for traffic initiated from the internal network..
How does Cisco Show ACL?
To display all IPv4 access control lists (ACLs) or a specific IPv4 ACL, use the show ip access-lists command.
What are the types of ACL?
There are four types of ACLs that you can use for different purposes, these are standard, extended, dynamic, reflexive, and time-based ACLs….What Are The Types of ACLs?Standard ACL. The standard ACL aims to protect a network using only the source address. … Extended ACL. … Dynamic ACL. … Reflexive ACL.
How do I check the ACL on my router?
show run will display the active configuration, including ACLs. There’s no command to do this in one go. You’ll need to show run
What is the difference between ACL and firewall?
ACL is a logic that will allow or deny a few packets passing through the interface. The difference between the two lies in how they are implemented. The firewall has just one purpose of examining traffic and blocking or allowing the traffic. … ACL does a stateless inspection, while Firewall handles a stateful inspection.
What is ACL authentication?
Web Server supports authentication and authorization through the use of locally stored ACLs, which describe what access rights a user has for a resource. …
Where is standard ACL applied?
Standard Access Control List (ACL) filters the traffic based on source IP address. Therefore a Standard Access Control List (ACL) must be placed on the router which is near to the destination network/host where it is denied.
Which scenario would cause an ACL misconfiguration and deny all traffic?
Which scenario would cause an ACL misconfiguration and deny all traffic? Apply an ACL that has all deny ACE statements. Having all ACEs with deny statements denies all traffic because there is an implicit deny any command at the end of every standard ACL.
What is the effect of configuring an ACL with only ACEs that deny traffic?
What is the effect of configuring an ACL with only ACEs that deny traffic? The ACL will permit any traffic that is not specifically denied. The ACL will block all traffic. The ACL must be applied inbound only.
How does Cisco ACL work?
An ACL is a list of permit or deny rules detailing what can or can’t enter or leave the interface of a router. Every packet that attempts to enter or leave a router must be tested against each rule in the ACL until a match is found. If no match is found, then it will be denied.
On which options are standard ACL based?
Access-list (ACL) is a set of rules defined for controlling the network traffic and reducing network attacks. ACLs are used to filter traffic based on the set of rules defined for the incoming or out going of the network. These are the Access-list which are made using the source IP address only.
What command will show you if an ACL is applied to an interface?
show ip interface commandUse the show ip interface command to verify that the ACL is applied to the correct interface. The output will display the name of the access list and the direction in which it was applied to the interface.
What is ACL command?
Each ACL includes an action element (permit or deny) and a filter element based on criteria such as source address, destination address, protocol, and protocol-specific parameters. …
What extended ACL?
Extended Access Control Lists (ACLs) allow you to permit or deny traffic from specific IP addresses to a specific destination IP address and port. It also allows you to specify different types of traffic such as ICMP, TCP, UDP, etc.
Where do you put an extended ACL?
Extended ACLs should be applied close to the source of the packets so that a packet is denied near the source to save router resources and bandwidth rather then it being forwarded close to the destination and eventually being denied.