Quick Answer: What Do You Put Behind A Wood Stove?

Do you tile behind stove?

Tile a Backsplash Behind or Around a Stove Protect the floor with towels and slide the stove forward and off to the side.

Gas ranges, larger electric ranges, and cooktops built into countertops are more difficult to remove from the work area..

How close can stove be to wall?

18 inchesAn unprotected stove pipe should be at least 18 inches from an unprotected wall or ceiling.

How far does a wood stove need to be away from a brick wall?

36 inchesCirculating air will cool the panel and wall behind it (Figure 1). At least 36 inches of clearance must be allowed between the top of a stove and an unprotected ceiling. Brick or stone provide little or no protection for a combustible wall since they are good conductors of heat.

Can you put stove next to wall?

Ranges: Electric ranges require 0″ side wall spacing above counter height, but up to 6″ is recommended to avoid possible heat damage. Please review specific model installation instructions for required dimensions. Gas ranges require 1″- 6″side wall spacing above the counter height for proper combustion.

How much space do you need for a 30 inch stove?

As far as the range, 30 1/4” is standard for a 30” stove. Any less makes it hard for the installer and the customer if they ever want to slide it out. I feel you should never go less than 30 1/8”. As far as the refrigerator goes, I think it would be better to allow a little more if you can.

Are cement boards fireproof?

Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.

What can be used as a heat shield?

Put simply, a heat shield is any kind of barrier that stops or limits heat from getting through….The materials we use to make our heat barriers and insulators vary but generally include:Fiberglass and fiberglass yarn.Aluminum.Stainless Steel.Basalt (volcanic rock)Silica.

Is durock fire resistant?

A Durock panel with a thickness of 1/2 or 5/8 inch can provide two hours of fire protection when installed correctly and in conjunction with all fireproofing construction materials.

Can you use cement board behind a wood stove?

Safe wood stove installations require a heat shield that will prevent heat from the wood stove from creating a fire hazard in the building materials that form the exterior wall. Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application.

Can I tile behind a wood burning stove?

ANSWER. ANSWER – Ceramic tile behind a woodstove works very well as long as it’s installed correctly over the right type of substrate. … It’s important, though, that the tile is attached to a surface that’s not affected by heat. It’s best to use a concrete substrate like a mortar bed or a cementitious backer unit.

Can I use cement board as a heat shield?

Used as a wall protector/heat shield, PermaBase Cement Boards reduces by 40% the manufacturer- specified clearance (minimum 12”) between the room heater or stove and a combustible wall surface. … Heat build-up is reduced by allowing air to enter and exit the cavity between the wall and the heat shield.

How much space is needed around a wood burning stove?

150mm (6″) minimum space from the sides of the stove to the non-combustible fireplace inner side walls. This can be reduced slightly but must be compensated by a much greater space at the top of the stove.

Can you tile onto Fireboard?

You can tile directly onto that once it has dried out thoroughly (4 weeks). For the tiles, you will need to use a quality trade (not own brand or DIY crap) powder cement adhesive (not tub mix) which will withstand heat of around 150 degrees; I use BAL Rapidset.

How do you protect a wall behind a wood stove?

Insulation Board Heat Shields Another—perhaps simpler—answer to the wood stove heat dissipation problem can be found right at your local heating supply store. Buy a 4′ by 10′ sheet of foil-covered fiberglass duct board, and slice it to match the dimensions of the wall area you’re going to protect.

What is considered a non combustible wall?

While wall ‘coverings’ are frequently non-combustible — like tile, brick, stone, metal — the underlying structure often contains wood, paper faced drywall or insulation, and other materials that could catch fire if enough heat were to be transmitted through the ‘non-combustible’ wall covering.

Is cement board considered non combustible?

Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.

Is tile adhesive heat resistant?

Vitcas® Heat Resistant Tile Adhesive is a ready mixed tile cement specially formulated for use in high temperature conditions where ordinary tile cements are inadequate for the long term retention of tiles.